AED
USD
EUR
QAR
SAR
- Description
Specifications
|
FEATURES
|
Selectable S-FHSS and FHSS modes, the included R2006GS receiver
automatically adapts to the selected mode
Capable of 4 channels only in FHSS mode
Fail safe on all channels in S-FHSS mode only (throttle channel only
when FHSS mode is selected)
15 model memory with 4 character model naming
40x40 127 segment LCD display
Modes 1-4 selectable by pilot
R2006GS high-voltage (4.8 - 7.4V) 6-channel receiver with Easy-Link
circuitry, frequency hopping, spread spectrum design and Dual
Antenna Diversity
Endpoint adjustment (EPA), sub trims, servo reversing & throttle cut
Throttle position, mix and low battery warnings
Trainer system (trainer cord not included)
One year limited warranty through Hobby Services beginning at date of
purchase
Airplane Features;
Two programmable mixes and two 5-point throttle curves
Two 5-point pitch curves
Flaperon with differential rate
Flap trim (2 rates)
V-tail mixing
Elevon mixing
Helicopter Features;
Two 5-point throttle curves
Three 5-point pitch curves
Throttle hold
Hover pitch
Gyro and revo mixing
Four swash plate types (H1, H3, HR3 & H3 w/AFR)
Swash AFR (ail/ele/pitch)
Throttle mix
Electronic swash ring
Throttle and pitch delay
automatically adapts to the selected mode
Capable of 4 channels only in FHSS mode
Fail safe on all channels in S-FHSS mode only (throttle channel only
when FHSS mode is selected)
15 model memory with 4 character model naming
40x40 127 segment LCD display
Modes 1-4 selectable by pilot
R2006GS high-voltage (4.8 - 7.4V) 6-channel receiver with Easy-Link
circuitry, frequency hopping, spread spectrum design and Dual
Antenna Diversity
Endpoint adjustment (EPA), sub trims, servo reversing & throttle cut
Throttle position, mix and low battery warnings
Trainer system (trainer cord not included)
One year limited warranty through Hobby Services beginning at date of
purchase
Airplane Features;
Two programmable mixes and two 5-point throttle curves
Two 5-point pitch curves
Flaperon with differential rate
Flap trim (2 rates)
V-tail mixing
Elevon mixing
Helicopter Features;
Two 5-point throttle curves
Three 5-point pitch curves
Throttle hold
Hover pitch
Gyro and revo mixing
Four swash plate types (H1, H3, HR3 & H3 w/AFR)
Swash AFR (ail/ele/pitch)
Throttle mix
Electronic swash ring
Throttle and pitch delay
|
INCLUDES
|
Futaba 6J 6-Channel Transmitter, R2006GS Receiver, Instruction
Manual, Neckstrap and Smooth Ratchet Plate for Heli Throttle
Manual, Neckstrap and Smooth Ratchet Plate for Heli Throttle
|
REQUIREMENTS
|
AA Cells: Four for transmitter
Servos of modeler's choice
Receiver battery
(See COMMENTS for optional battery and charger choices)
Servos of modeler's choice
Receiver battery
(See COMMENTS for optional battery and charger choices)
|
SPECIFICATIONS
|
Transmitter;
Type: 2-stick, 6-channel, FHSS/S-FHSS selectable
Frame Rate: 6.8ms
Current Drain: 170mA
Receiver;
Modes: FHSS or S-FHSS (auto selectable)
Power Requirements: 4.8V-7.4V
Compatible Batteries: NiCd, NiMH, LiPo, LiIon & LiFe
Dimensions: 1-11/16 x 15/16 x 5/16" (43 x 24 x 7.9mm)
Weight: 0.29oz (8.3g)
Current Drain: 80mA (@ no signal)
Type: 2-stick, 6-channel, FHSS/S-FHSS selectable
Frame Rate: 6.8ms
Current Drain: 170mA
Receiver;
Modes: FHSS or S-FHSS (auto selectable)
Power Requirements: 4.8V-7.4V
Compatible Batteries: NiCd, NiMH, LiPo, LiIon & LiFe
Dimensions: 1-11/16 x 15/16 x 5/16" (43 x 24 x 7.9mm)
Weight: 0.29oz (8.3g)
Current Drain: 80mA (@ no signal)
|
COMMENTS
|
You may also use a 2C 6.6V LiFe battery such as HCAM6521
If you are wanting to ue a LiFe or NiMh battery with this
transmitter, you will need to purchase the NiMh battery
door from Futaba Service at 217-398-8970 part number HSP82469
To charge through the transmitter, you will need a lead from
Futaba Service, part number HSP29615. This is only the TX jack
with leads that you will need to solder connectors onto to use
with your charger.
Or you can purchase the 4PK charger FUTM1832
If you are wanting to ue a LiFe or NiMh battery with this
transmitter, you will need to purchase the NiMh battery
door from Futaba Service at 217-398-8970 part number HSP82469
To charge through the transmitter, you will need a lead from
Futaba Service, part number HSP29615. This is only the TX jack
with leads that you will need to solder connectors onto to use
with your charger.
Or you can purchase the 4PK charger FUTM1832
You May Like
-
AED510.00
-
AED280.00
-
AED925.00
-
AED2,450.00
-
AED420.00
-
AED3,850.00
-
AED840.00
-
AED1,100.00
-
AED690.00
